September 19th (Alternative) Welding Safety

Safety Activity: Watch Hot Work Accidents video CSB "Dangers of Hot Work" (approx. 14 minutes)

Reference: WAC 296-24-680 and WAC 296-62-08003.

Frequency: Initial and as needed.

Note: Additional training may be required WELDING AND HEXAVALIUM CHROMIUM.

September 2nd Tool and Electrical Safety

Safety Topic: General Tool and Electrical Safety  (not Lock out/Tag Out)

Watch: Electrical Safety for Non-Electricians https://www.youtube.com/watch?v=ggJo6m8NZtA Note: the Standards quoted at the end are Canadian, but the information is excellent.

1.  Keep all tools away from the edges of scaffolding, platforms, shaft openings, etc.

2.  Do not use tools with split, broken, or loose handles; or burred or mushroomed heads. Keep cutting tools sharp and carry all tools in a container.

3.  Know the correct use of hand and power tools. Use the right tool for the job.

4.  Proper guards or shields must be installed on all power tools before use. Do not use any tools without the guards in their proper working condition. No “homemade” handles or extensions (cheaters) will be used!

5.  Do not “pin-back” guards on skill saws.

6.  Ensure table saws have appropriate guards and kick-back devices are installed before use.

7.  All electrical power tools and extension cords must be properly insulated. Damaged cords must be replaced.

8. All electrical power tools (unless double insulated), extension cords, and equipment must be properly grounded.

9.  Do not operate any power tool or equipment unless you are trained in its operation and authorized by your firm to do so.

10.  All power cords must be plugged into a GFCI outlet.

11.  Use proper personal protective equipment (PPE) while using power tools. Often safety glasses, hearing protection, dust masks and gloves are required with many tools.

12.  Check the height of your vehicle’s load and the height of the power lines before you go under.

13.  Safe distances: Maintain safe working distances from all overhead wires and power transmission lines. When operating mechanized equipment make sure that the equipment, or material being moved, is at least 10' away from power lines. Very high voltage levels (over 50 kv) require distances greater than 10'.

14. Ladder, tools, and equipment: Employees should be aware of the hazards of working with ladders near power lines. Ensure that ladders, scaffolds, pipes, window washing rollers, other types of tools and materials do not come within 10' of power lines.

15. Pneumatic tools and hoses shall be connected by positive means and safety clips used to prevent accidental disconnection.

Reference: WAC 296-800-200.

Frequency: Initial and as needed.

Note:  Lock Out / Tag Out will be addressed in an upcoming meeting

July 8th Fall Protection Equipment Inspection

Safety Activity: Inspect all Fall Protection Equipment, Ropes, Harnesses and connections per the manufacturer's recommendations.  Document the inspection on a form or the actual harness if it has a tag.

Supervisor: Order new equipment for your employees as needed/found out during this activity.

Reference: WAC 296-155-24605

Frequency: Before each use and per the manufacturer's recommendation.

Notes: Contact Kris at nicasaftey@gmail.com for recommendations on fall protection equipment if needed.

July 1st Fall Protection Awareness Month

Safety Activity: Watch 20 minute safety video "Don't Hit the Ground"

Supervisor: Review Fall Protection (12) section of Safety Plan.

Reference: WAC 296-155-24621

Frequency: Initial and as needed

Notes: Competent person training is required for those who setup fall protection systems. If needed contact Kris at nicasaftey@gmail.com to schedule training.

June 24th Run, Hide, Fight

Safety Activity:  Watch Run, Hide, Fight

Supervisor: Discuss workplace violence and ways to escape active shooters.

June 17th Hierarchy of Controls

Safety Activity: Watch this 3 minute video on the Hierarchy of Controls

Safety Topic: Administrative Controls: Are procedures for safe work methods that reduce the duration, frequency, or severity of exposure to a hazard. Administrative controls include gradual introduction to work, regular recovery pauses, job rotation, job design and maintenance and housekeeping. One example would be redesigning a job that normally requires two hours of continuous handling, to include a five-minute recovery period (performing housekeeping duties with little or no manual handling) for every 15 minutes of continuous handling.

Supervisor:

Reference:

Frequency: Initial and as needed.

Notes:

June 10th Equipment Safety

Safety Activity:  Choose one piece of company equipment and review the manufacturer's safety rules.  Focus on pinch points, caught in between, struck by, electrocution, and fall hazards associated with the piece of machinery.

Alternate Class: Show how to safely handle LPG tanks.

Supervisor: Choose key equipment and review safety features and requirements.

Reference:

Frequency: Initial and as needed.

Notes: